Diamond saw blades(for marble/dekton/concrete)
Diamond Saw Blade for Marble
Diamond segmented circular saw blade for marble, 350 to 600 mm, 40 mm segment with 8 to 10 mm height, bore 50 or 60 mm, for bridge saws and wet cut-off saws.
Specifications
- Type
- Diamond segmented circular saw blade, welded segments
- Application
- Marble and other soft, non-abrasive stone
- Diameter
- 350 mm, 400 mm, 450 mm, 500 mm, 600 mm
- Segment size
- 40 mm segment, 2.6 to 4.5 mm thickness, 8 to 10 mm height
- Bore
- 50 mm or 60 mm
- Cutting
- Wet cutting on bridge saws and wet cut-off saws
- Customization
- Other sizes produced to order
Marble is soft and cuts fast, so the blade for it is built around a thin plate and a shallow segment rather than around wear resistance. A 2.6 mm segment on the 350 mm size keeps the cut narrow and the load on the bridge saw low, which is what lets the head feed at a steady rate without the plate bowing.
What the segment does
The diamond grit in the segment grinds the stone away, and the metal bond around it has to wear back at the same rate to keep fresh grit exposed. In marble that balance is easy to hold: the material is not abrasive enough to wear the bond quickly, so a comparatively hard bond lasts and the segment keeps its shape.
A blade that stops cutting in marble is usually glazed rather than worn out: the bond has polished over and the grit is blunt. Dressing it on an abrasive block restores the cut.
Available sizes
350 mm (14 in) — 350 x 40 x 2.6 x 8 — bore 50 / 60 mm — segment height 8 mm
400 mm (16 in) — 400 x 40 x 3.0 x 8 — bore 50 / 60 mm — segment height 8 mm
400 mm (16 in) — 400 x 40 x 3.4 x 10 — bore 50 / 60 mm — segment height 10 mm
450 mm (18 in) — 450 x 40 x 3.4 x 8 — bore 50 / 60 mm — segment height 8 mm
500 mm (20 in) — 500 x 40 x 3.8 x 8 — bore 50 / 60 mm — segment height 8 mm
600 mm (24 in) — 600 x 40 x 4.5 x 8 — bore 50 / 60 mm — segment height 8 mm
Rows are transcribed from the manufacturer catalogue and keep its printed order: diameter, segment size, thickness, segment height, then bore. Other sizes are produced to order.
Ordering
Send the machine type (bridge saw, wet cut-off saw or hand-held wet saw), the diameter, the bore and the segment height you want. If you are replacing a blade, a photograph of the marking on the old one is enough to match the specification.
Frequently asked questions
What do I check before ordering?
Three things decide whether the blade fits: the outer diameter against the saw capacity, the bore against the spindle, and the segment height against the material. The bore is printed on the old blade and easy to measure; the pin-hole or drive pattern is where machines of the same brand often differ, so check it before the blade is made.
What does segment height change?
Segment height is the working life of the blade: a taller segment cuts for longer between changes, a shorter one costs less per blade. On hard material a taller segment also keeps the plate further from the cut, which matters once the segment starts to wear.
Wet or dry cutting?
Stone and engineered surfaces are normally cut wet on a bridge saw or a wet hand saw: water keeps the segment cool and controls dust. Concrete is often cut dry where water is impractical, and that needs a segment built for the higher temperature. Tell us which you run and the blade is specified for it.
Can the bore or diameter be changed?
Yes. Diameter, segment height, thickness, segment width and bore are produced to the machine. Send the machine make and model plus the marking on the old blade, and the specification is confirmed against that rather than against the nearest stock size.
